How to | Learning

How To Restring Your .strandberg* Guitar

In this second installment of our How To series, our goal is to get you familiar with the tools and techniques required to restring your .strandberg* guitar the easy way.

We will illustrate how to change your strings one at a time instead of removing them all at once. Using this method is the simplest for floating tremolo guitars, and equally applicable to our hardtails. Stay tuned for a coming detailed article about setup and advanced topics concerning our tremolo.

The Tools

Before changing the strings on your .strandberg* guitar we highly recommend having the following list of tools on hand to make your string changing experience an easy one.

  1. Small Flat Head Screwdriver
  2. 6mm T Wrench
  3. 3mm Allen Wrench
  4. String Clippers

1. Loosen The Tension Of The Strings

To remove the old strings, insert the 6mm T wrench into the end of tuner for the string that you want to change and turn counter-clockwise to loosen the tension of the strings. You can also perform this task with your fingers however using the 6mm T wrench will make easier and faster for you.

2. Loosen The String Locks

Once you have relieved tension of the string, use the 3mm Allen wrench to loosen the string lock and remove the old string from the nut.

3. Remove The String From The Bridge

Now that the string is no longer locked use your hand to push the ball end of the string out of the bridge’s tuner assembly.

4. Prepping The Tuner

Before restringing we recommend prepping the tuner assembly to ensure you have a good range of +/- tuning after you lock down the string.

  1. Remove the cap from the shaft of the tuner assembly with your hands by turning counter-clockwise.

2. With your hands reattach the cap to the shaft of the tuner assembly using 3 clock-wise turns.

3. Once the cap is reattached, push the tuner shaft flush with the tuner assembly.

4. Now you are ready to restring.

5. Restringing (Bridge)

  1. Take a new string and thread it through the cap of the tuner assembly.

2. Using a small flat head screw driver, lift the string gently then pull it using your fingers and place it over the top of the saddle.

3. Now you’re ready to lock it.

6. Restringing (Nut)

  1. Thread the string through the opening of string lock.

2. Using your hand, pull the string straight and taught to ensure it is secured before tightening down the string lock.

7. Tightening The String Lock  

While holding the string straight, use a 3mm Allen wrench in the vertical position (shown) to tighten the string lock. Important: Be sure not to over tighten, as this may cause damage to the components of your instrument.

8. Clipping The Strings

Once the string is locked, position your string clippers flush with the top of the string locks and clip the string.

Using this clipping technique will tame the ends of the strings and provide a nice almost flat surface that reduces the chance of pricking your fingers.

9. Tune Up

Use the 6mm T wrench to tune up and you are ready to go.

We hope that this article was able to shed some light on restringing your .strandberg* guitar. Next time we will introduce you to the truss rod, it’s purpose, and How To Adjust it.

If you are wondering where to get a set of nifty string cutters like the pair used this article, they are available as part of our .strandberg* Deluxe Toolkit available through our web-store.

Strandberg Magazine

Recent Articles

SPARK Community – June

SPARK Community - June The SPARK community has done it again! During the month of June the community was tasked with developing creative ways to show their enthusiasm and support for .strandberg* instruments based on…

Read More

Error: Access Token is not valid or has expired. Feed will not update.
This error message is only visible to WordPress admins

There's an issue with the Instagram Access Token that you are using. Please obtain a new Access Token on the plugin's Settings page.
If you continue to have an issue with your Access Token then please see this FAQ for more information.